Page 1 of 1
A Motherboard or PSU Problem?
Posted: Fri Jan 02, 2004 6:21 pm
by Hunter
Well, I'll get straight down to the point here - Power problems. I've noticed over time my system doesn't like power surges, I.E inserting a USB device such as a scanner or modem that draws power from the system. So, I just assumed it was one of those things, until the other day I put a Network Card in to then find after booting that my Terratec's Frontpanel drive-bay couldn't get any power. The card works fine, but not the bay - Which draws a small amount of power like a USB device, for those unfamiliar with the DMX6Fire Frontbay. So then I took the card out, decided it wasn't needed at this moment in time.
The following day, today, I put another hard-drive in for backing up some large files and other essentials. Same problem, the bay can't get any power to switch on (otherwise known as unstick from "Peak Limit").
Anyone got any ideas?
Hunter
Posted: Fri Jan 02, 2004 6:46 pm
by Tetrad
Well obviously I know the answer given the very good discription of your system in your post.
(That was sarcasm by the way, post your motherboard/processor as well as PSU brand and wattage, lest we not be able to help you.)
Posted: Fri Jan 02, 2004 9:50 pm
by Mr. Perfect
The hard drive draws it's power straight from the power supply, so I'm betting it's that.
Posted: Sat Jan 03, 2004 7:53 am
by Hunter
<b>
XP1800
PC-Chips Motherboard (Fah!)
512+128mb SD133RAM
40GB HDD
Geforce 3 ti500
DMX6Fire
CODEGEN 300W
ATX 2.03 (P4)
MODEL 300X
AC INPUT 115/230VAC - 8a/4a 60/50hz
AC OUTPUT 115/230VAC - 1a/0.5a 50/50hz
Tsunami CPU Fan & System Fan + Rear mounted exhaust fan.
</b>
Oh and - Typical Descent Bang Boys reply.
EDIT: After some fiddling problem seems resolved... I think
Posted: Sat Jan 03, 2004 3:37 pm
by Mobius
350 Watts is recommended for Athlon XP systems. You are 50 watts short.
Don't forget: V=I*R
Where V = volts, I = Amps and R = Resistance (Watts)
So, this means, as your load on the powersupply increases the voltages drop. It's quite possible that components are smart enough to know when voltages are too low for consistent operation, and would fail to start up.
Check your Motherboard voltages - they should be VERY close to the spec.
Posted: Sat Jan 03, 2004 4:26 pm
by Tetrad
I'm not familar with that brand of PSU. Try running Motherboard Monitor and make sure your voltages are close to what they should be, especially your 12volt rail.
Posted: Sat Jan 03, 2004 8:57 pm
by Mobius
I would use the BIOS voltage monitor ahead of MBM.
Posted: Sun Jan 04, 2004 5:42 am
by Hunter
Right, thanks. I need to replace the PSU anyway, and some fans.
Noisy pos.
Posted: Sun Jan 04, 2004 6:25 am
by Admiral LSD
<BLOCKQUOTE><font size="1" face="Arial">quote:</font><HR><font face="Arial" size="3">Originally posted by Mobius:
350 Watts is recommended for Athlon XP systems. You are 50 watts short.</font><HR></BLOCKQUOTE>
I run my Athlon XP 2400+ system on a 300W supply without any issues...
Posted: Sun Jan 04, 2004 11:26 am
by fliptw
<BLOCKQUOTE><font size="1" face="Arial">quote:</font><HR><font face="Arial" size="3">Originally posted by Admiral LSD:
<b> I run my Athlon XP 2400+ system on a 300W supply without any issues...
</b></font><HR></BLOCKQUOTE>
But, you aren't Mobius.
Posted: Sun Jan 04, 2004 1:02 pm
by MD-2389
Hunter, how much current is the power supply supposed to be able to handle on the 12V rail? (should tell you on the label on the power supply)